loadrt	trivkins
loadrt	[EMCMOT]EMCMOT			base_period_nsec=[EMCMOT]BASE_PERIOD servo_period_nsec=[EMCMOT]SERVO_PERIOD traj_period_nsec=[EMCMOT]SERVO_PERIOD key=[EMCMOT]SHMEM_KEY num_joints=[TRAJ]AXES

loadrt	stepgen				step_type=0,0,0
loadrt	charge_pump
loadrt	comp				count=3
loadusr -W hal_manualtoolchange

# Base thread
addf	stepgen.make-pulses		base-thread

# Servo thread
addf	stepgen.capture-position	servo-thread
addf	motion-command-handler		servo-thread
addf	motion-controller		servo-thread
addf	stepgen.update-freq		servo-thread
addf	charge-pump			servo-thread
addf	comp.0				servo-thread
addf	comp.1				servo-thread
addf	comp.2				servo-thread

# Spindle control
net	spindle-cw			<= motion.spindle-forward
net	spindle-ccw			<= motion.spindle-reverse

# Coolant control
net	coolant-mist			<= iocontrol.0.coolant-mist
net	coolant-flood			<= iocontrol.0.coolant-flood

# heartbeat generator
setp	charge-pump.enable		1
net	heartbeat			<= charge-pump.out-4

# Emergency stop logic
net	estop-out-not			<= iocontrol.0.user-enable-out
net	estop-in-not			=> iocontrol.0.emc-enable-in

# Manual tool change
net	tool-change			iocontrol.0.tool-change		=> hal_manualtoolchange.change
net	tool-changed			iocontrol.0.tool-changed	<= hal_manualtoolchange.changed
net	tool-number			iocontrol.0.tool-prep-number	=> hal_manualtoolchange.number
net	tool-prepare-loopback		iocontrol.0.tool-prepare	=> iocontrol.0.tool-prepared

# X joint
setp	stepgen.0.position-scale	[AXIS_0]SCALE
setp	stepgen.0.steplen		[STEPCONF]STEPLEN
setp	stepgen.0.stepspace		[STEPCONF]STEPSPACE
setp	stepgen.0.dirhold		[STEPCONF]DIRHOLD
setp	stepgen.0.dirsetup		[STEPCONF]DIRSETUP
setp	stepgen.0.maxaccel		[AXIS_0]STEPGEN_MAXACCEL
net	xpos-cmd			axis.0.motor-pos-cmd => stepgen.0.position-cmd
net	xpos-fb				stepgen.0.position-fb => axis.0.motor-pos-fb
net	xstep				<= stepgen.0.step
net	xdir				<= stepgen.0.dir
net	xenable				axis.0.amp-enable-out => stepgen.0.enable
net	home-x				=> axis.0.home-sw-in
net	limit-x				=> axis.0.neg-lim-sw-in
net	limit-x				=> axis.0.pos-lim-sw-in

# Y joint
setp	stepgen.1.position-scale	[AXIS_1]SCALE
setp	stepgen.1.steplen		[STEPCONF]STEPLEN
setp	stepgen.1.stepspace		[STEPCONF]STEPSPACE
setp	stepgen.1.dirhold		[STEPCONF]DIRHOLD
setp	stepgen.1.dirsetup		[STEPCONF]DIRSETUP
setp	stepgen.1.maxaccel		[AXIS_1]STEPGEN_MAXACCEL
net	ypos-cmd			axis.1.motor-pos-cmd => stepgen.1.position-cmd
net	ypos-fb				stepgen.1.position-fb => axis.1.motor-pos-fb
net	ystep				<= stepgen.1.step
net	ydir				<= stepgen.1.dir
net	yenable				axis.1.amp-enable-out => stepgen.1.enable
net	home-y				=> axis.1.home-sw-in
net	limit-y				=> axis.1.neg-lim-sw-in
net	limit-y				=> axis.1.pos-lim-sw-in

# Z joint
setp	stepgen.2.position-scale	[AXIS_2]SCALE
setp	stepgen.2.steplen		[STEPCONF]STEPLEN
setp	stepgen.2.stepspace		[STEPCONF]STEPSPACE
setp	stepgen.2.dirhold		[STEPCONF]DIRHOLD
setp	stepgen.2.dirsetup		[STEPCONF]DIRSETUP
setp	stepgen.2.maxaccel		[AXIS_2]STEPGEN_MAXACCEL
net	zpos-cmd			axis.2.motor-pos-cmd => stepgen.2.position-cmd
net	zpos-fb				stepgen.2.position-fb => axis.2.motor-pos-fb
net	zstep				<= stepgen.2.step
net	zdir				<= stepgen.2.dir
net	zenable				axis.2.amp-enable-out => stepgen.2.enable
net	home-z				=> axis.2.home-sw-in
net	limit-z				=> axis.2.neg-lim-sw-in
net	limit-z				=> axis.2.pos-lim-sw-in

# Simulate home switches
net	xpos-cmd			=> comp.0.in0
setp	comp.0.in1			0
setp	comp.0.hyst			0.1
net	home-x				<= comp.0.out

net	ypos-cmd			=> comp.1.in0
setp	comp.1.in1			0
setp	comp.1.hyst			0.1
net	home-y				<= comp.1.out

net	zpos-cmd			=> comp.2.in0
setp	comp.2.in1			0
setp	comp.2.hyst			0.1
net	home-z				<= comp.2.out

# Simulate hardware limit switches
sets	limit-x				0
sets	limit-y				0
sets	limit-z				0