blob: 2c368619e06452e7095041faf6f62349220fa740 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
# BCM95351BU SDRAM board
# Copyright 2007, Broadcom Corporation
# All Rights Reserved.
#
# THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
# KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
# SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
# FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
# $Id: bcm95351bu_sdram.txt,v 1.1.1.1 2008/07/21 09:20:53 james26_jang Exp $
boardtype=0x047a
boardnum=${serno}
# VLAN + ROBO
boardflags=0x0110
# Board revision 1.0
boardrev=0x11
# MIPS clock frequency in MHz
clkfreq=200
# 64 MB DDR SDRAM (4 Meg x 16 x 2)
sdram_init=0x0009
sdram_config=0x0062
sdram_refresh=0x0000
sdram_ncdl=0
# Bootloader variables
dl_ram_addr=a0001000
os_ram_addr=80001000
os_flash_addr=bfc40000
lan_ipaddr=192.168.1.1
lan_netmask=255.255.255.0
scratch=a0180000
boot_wait=on
reset_gpio=3
# Watchdog timer in ms
watchdog=3000
# Ethernet w/Robo switch
et0macaddr=00:90:4c:9c:${maclo}
et0phyaddr=30
et0mdcport=0
# Robo switch config (vlan0:LAN, vlan1:WAN)
vlan0ports=1 2 3 4 5*
vlan0hwname=et0
vlan1ports=0 5u
# Bootloader and OS glue
landevs=vlan0 wl0 wl1
wandevs=et0
# SES parameters
gpio2=ses_button
#
# --- on-chip d11 device ---
#
sb/7/sromrev=2
# HGPA + AB + CCK + AD
sb/7/boardflags=0x2248
# single band 802.11b/g device
sb/7/devid=0x4320
# 802.11g parameters
sb/7/il0macaddr=00:90:4c:9d:${maclo}
sb/7/aa0=1
sb/7/ag0=255
sb/7/pa0maxpwr=76
sb/7/pa0itssit=62
sb/7/pa0b0=0x15c8
sb/7/pa0b1=0xfa80
sb/7/pa0b2=0xfe65
sb/7/opo=12
# LED GPIO assignments
sb/7/wl0gpio2=0
# misc. parameters
sb/7/ccode=0
#
# --- off-chip d11 device ---
#
pci/1/1/sromrev=2
# ALTIQ + HGPA + AB + CCK + AD
pci/1/1/boardflags=0xa248
# single band 802.11a device
# pci/1/1/devid=0x431a
# 802.11a parameters
# pci/1/1/et1macaddr=00:90:4c:9e:${maclo}
# pci/1/1/aa1=1
# pci/1/1/ag1=2
# pci/1/1/pa1lomaxpwr=60
# pci/1/1/pa1himaxpwr=60
# pci/1/1/pa1lob0=0x1880
# pci/1/1/pa1lob1=0xfcbd
# pci/1/1/pa1lob2=0xff4b
# pci/1/1/pa1hib0=0x18a8
# pci/1/1/pa1hib1=0xfcc1
# pci/1/1/pa1hib2=0xff41
# pci/1/1/pa1maxpwr=60
# pci/1/1/pa1b0=0x184c
# pci/1/1/pa1b1=0xfcc3
# pci/1/1/pa1b2=0xff40
# pci/1/1/pa1itssit=120
# pci/1/1/opo=0
# LED GPIO assignments
pci/1/1/wl0gpio0=2
pci/1/1/wl0gpio1=0
pci/1/1/wl0gpio2=4
# misc. parameters
pci/1/1/ccode=0
|
