aboutsummaryrefslogtreecommitdiffstats
path: root/examples/example_s7_315_2dp.conf
blob: 861d4f89cde9eabb63407c46dfbd7743533b5a75 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
; ----------------------------------------------- ;
;                                                 ;
; PROFIBUS configuration                          ;
;                                                 ;
; This file configures a pyprofibus instance.     ;
;                                                 ;
; ----------------------------------------------- ;


; General settings
[PROFIBUS]

; Enable/disable debug mode.
; 0 -> no debugging.
; 1 -> DP debugging.
; 2 -> DP and PHY debugging.
debug=1


; PHY protocol layer configuration
[PHY]

; The PHY layer driver type.
type=serial
;type=fpga
;type=dummy_slave

; Only for type=serial:
; The PHY device name/path.
; Can be a device like /dev/ttyS0 or /dev/ttyAMA0
dev=/dev/ttyS0

; Only for type=serial:
; Serial line flow control and handshaking
rtscts=False
dsrdtr=False

; Only for type=fpga:
; SPI bus (to PHY FPGA) configuration.
spiBus=0
spiCS=0
spiSpeedHz=2500000

; The Profibus on-wire baud rate.
;baud=9600
baud=19200
;baud=45450
;baud=93750
;baud=187500
;baud=500000
;baud=1500000
;baud=3000000
;baud=6000000
;baud=12000000


; FDL protocol layer configuration
[FDL]


; DP protocol layer configuration
[DP]

; The master device class. Either 1 or 2.
master_class=1

; The Profibus address of this device.
master_addr=2


; ---
; Slave configurations
; Add as many [SLAVE_xxx] sections as needed.
; ---

; First slave configuration
[SLAVE_0]

; Optional slave name. Will be stored in slaveConf.name and slaveDesc.name.
; pyprofibus does not use the name internally.
name=s7_315_2dp

; This slave's Profibus address
addr=9

; The path to the GSD file.
gsd=sie3802f.gsd

; Boolean: Sync mode enabled/available?
sync_mode=0

; Boolean: Freeze mode enabled/available?
freeze_mode=0

; 8 bit integer specifying the Profibus group ident mask.
group_mask=1

; This slave's watchdog timeout, in milliseconds.
watchdog_ms=0

; Module configuration.
; For each module plugged into the slave, add a module_xxx
; entry with the name of the module.
; The module name must match the name from the GSD file (approximately).
; The modules are used in the order of the index number.
module_0=Master_O Slave_I  1 by unit
module_1=Master_I Slave_O  1 by unit

; The number of output bytes this slave transmits to the
; master in Data_Exchange.
; This usually depends on the modules plugged into the slave.
output_size=1

; The number of input bytes this slave expects to receive
; in Data_Exchange.
; This usually depends on the modules plugged into the slave.
input_size=1

; Request and interpret a slave diagnosis every n Data_Exchange telegrams.
; n defaults to 0, which means: Never periodically request diagnosis.
; If periodic diagnosis is switched off, then diagnostic information will only be requested on faults.
; Note that input-only slaves (output_size=0) probably need a non-zero diag_period.
diag_period=0
bues.ch cgit interface