blob: cf75bc665f2dc36b29474f7ac4830e28e9821e94 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
; ----------------------------------------------- ;
; ;
; PROFIBUS configuration ;
; ;
; This file configures a pyprofibus instance. ;
; ;
; ----------------------------------------------- ;
; General settings
[PROFIBUS]
; Enable/disable debug mode.
; 0 -> no debugging.
; 1 -> DP debugging.
; 2 -> DP and PHY debugging.
debug=1
; PHY protocol layer configuration
[PHY]
; The PHY layer driver type.
type=serial
; The PHY device name/path.
; Can be a device like /dev/ttyS0 or /dev/ttyAMA0 for 'serial'.
dev=/dev/ttyS0
; The Profibus on-wire baud rate.
baud=19200
; FDL protocol layer configuration
[FDL]
; DP protocol layer configuration
[DP]
; The master device class. Either 1 or 2.
master_class=1
; The Profibus address of this device.
master_addr=2
; ---
; Slave configurations
; Add as many [SLAVE_xxx] sections as needed.
; ---
; First slave configuration
[SLAVE_0]
; Optional slave name. Will be stored in slaveConf.name and slaveDesc.name.
; pyprofibus does not use the name internally.
name=et200s
; This slave's Profibus address
addr=8
; The path to the GSD file.
gsd=si03806a.gsd
; Boolean: Sync mode enabled/available?
sync_mode=1
; Boolean: Freeze mode enabled/available?
freeze_mode=1
; 8 bit integer specifying the Profibus group ident mask.
group_mask=1
; This slave's watchdog timeout, in milliseconds.
watchdog_ms=300
; Module configuration.
; For each module plugged into the slave, add a module_xxx
; entry with the name of the module.
; The module name must match the name from the GSD file (approximately).
; The modules are used in the order of the index number.
module_0=6ES7 138-4CA01-0AA0 PM-E DC24V
module_1=6ES7 132-4BB30-0AA0 2DO DC24V
module_2=6ES7 132-4BB30-0AA0 2DO DC24V
module_3=6ES7 131-4BD01-0AA0 4DI DC24V
; The number of output bytes this slave transmits to the
; master in Data_Exchange.
; This usually depends on the modules plugged into the slave.
output_size=1
; The number of input bytes this slave expects to receive
; in Data_Exchange.
; This usually depends on the modules plugged into the slave.
input_size=2
; Request and interpret a slave diagnosis every n Data_Exchange telegrams.
; n defaults to 0, which means: Never periodically request diagnosis.
; If periodic diagnosis is switched off, then diagnostic information will only be requested on faults.
; Note that input-only slaves (output_size=0) probably need a non-zero diag_period.
diag_period=0
|
